Tumbler Epoxy Calculator
Enter your tumbler size and how many coats you plan, and get the epoxy you need per coat in ml and oz, already split into resin and hardener for your brand’s ratio.
Tumbler epoxy calculator
Pick your tumbler, and how much epoxy to mix shows up here.
Design Nexus newsletter
Making glitter tumblers?
Get tumbler tips, wrap templates and new calculators as soon as they are out.
How the amount is worked out
The calculator works out the area of the tumbler's outside wall from its circumference at the top and bottom and the height you coat. A tapered tumbler is a slice of a cone, so the sloped side counts, not only the height.
That area times the thickness of one coat is the epoxy that ends up on the tumbler. A standard coat of about 0.2 mm comes to around 10 ml on a 20 oz skinny, which is what many tumbler makers mix. Then 15% is added for what stays in the cup and on the stir stick.
The mix is split by volume at the ratio you pick. If your epoxy's ratio is by weight, follow the weights on the bottle instead. Your brand's instructions always come first.
How much epoxy for a tumbler
| Tumbler | Per coat | 2 coats | Resin + hardener per coat, 1:1 |
|---|---|---|---|
| 12 oz kids skinny, straight | 0.27 fl oz | 0.54 fl oz | 0.14 fl oz + 0.14 fl oz |
| 20 oz skinny, straight | 0.38 fl oz | 0.76 fl oz | 0.19 fl oz + 0.19 fl oz |
| 30 oz skinny, straight | 0.45 fl oz | 0.9 fl oz | 0.23 fl oz + 0.23 fl oz |
| 20 oz skinny, tapered | 0.34 fl oz | 0.67 fl oz | 0.17 fl oz + 0.17 fl oz |
| 40 oz tumbler with handle | 0.44 fl oz | 0.87 fl oz | 0.22 fl oz + 0.22 fl oz |
| 16 oz glass can | 0.19 fl oz | 0.38 fl oz | 0.09 fl oz + 0.09 fl oz |
A standard coat on the outside wall, 15% extra for the cup included. Tumbler sizes are approximate; measure yours in the calculator.
How the calculator works
The amount of epoxy a coat takes depends on the surface you’re covering, so the calculator starts with the tumbler’s outside area. Pick a preset like a 20 oz skinny, or enter the top diameter, bottom diameter and height for anything else. Tapered cups get the cone formula, which matters on a 30 oz tumbler where the top is wider than the base.
That area is multiplied by a per-coat rate we set from our own test cups. If your coats run thicker or thinner, adjust the rate once and the calculator remembers it next time.
The total is then split by ratio. Most tumbler epoxies mix 1:1, and some mix 2:1. Read the label, set the ratio once, and the calculator saves that too.
Measure the way the label tells you
A ratio printed on the bottle is either by volume or by weight, and the two aren’t interchangeable.
A 2:1 by volume epoxy can come out at a different ratio by weight because the two parts have different densities. If your label gives volume, use medicine cups with printed lines. If it gives weight, use a scale.
Off-ratio epoxy can leave a tumbler tacky for days. Extra hardener won’t make it cure faster.
Mix a little extra
Some epoxy always stays on the cup walls and the stir stick. The calculator adds a small buffer you can turn off. For a first tumbler, leave it on: running short halfway around the cup is worse than throwing away a few ml.
Worked example
You’re coating a 20 oz skinny in fine glitter and plan three coats. The calculator gives the epoxy per coat, and you mix each coat fresh just before you apply it.
If a coat comes out at 12 ml with a 1:1 epoxy, you mix 6 ml of resin and 6 ml of hardener. Switch the ratio to 2:1 and the same 12 ml becomes 8 ml of resin and 4 ml of hardener. In ounces, 12 ml is about 0.4 fl oz.
Chunky glitter usually needs an extra coat to bury the edges, so add one to your count before you buy epoxy.
Before you pour
Wear gloves and work somewhere you can leave the cup turning undisturbed. A heat gun pops surface bubbles, but only before the epoxy starts to set. ArtResin lists 18 to 24 hours until dry to the touch and 72 hours to a full cure. Check your own brand’s times on the label.
Related tools
Sizing a sublimation or vinyl wrap under the epoxy? The tumbler wrap template calculator gives the wrap size for straight and tapered cups. For mugs and glass cans, use the mug and cup decal size calculator. When you’re ready to sell, the craft pricing calculator turns your material costs and time into a price. More tools are on the craft tools hub.
FAQ
How much epoxy do I need for a tumbler?
It depends on the cup’s surface area, how many coats you apply and how thick each coat is. Enter your tumbler and coats above for a number.
How many coats of epoxy does a glitter tumbler need?
Fine glitter often smooths out in two or three coats. Chunky glitter needs more, because each coat has to cover the raised edges.
Should I mix resin and hardener by volume or weight?
Follow the label. Most tumbler epoxies give a volume ratio, and switching to weight for the same ratio can throw the mix off.
Can I mix one big batch for all coats?
No. Epoxy starts to set in the cup, so mix each coat fresh.
